Warmtech’s undercarpet heaters use heating mats strategically placed wherever required. Positioned between the carpet and underlay, the heating mats are available in a range of shapes and sizes designed to fit most rooms. There’s no maintenance required, and no annual checkups are needed. With efficient zoning and a programmable thermostat, it’s easy to regulate your home’s temperature while saving energy and money.SHOP NOW
With all features completely hidden, there’s no threat to prying little fingers! Our heating elements and controls are approved to International standards. Our heating elements come with a 2-year warranty.
Already know what you are looking for?Undercarpet Brochure
These heating elements use 200 – 3000 watts, depending on the size of the room.
Electric underfloor heating provides more additional benefits than any other form of home heating. Used either as a primary heating source for whole house heating or as comfort heating to keep the chill off your cold floors, Warmtech has the electric underfloor heating system for you. Whether you are a contractor looking to install underfloor heating in a large development or a homeowner looking to install underfloor heating in a single room, Warmtech has the products and support to make your project run smoothly. With Warmtech, a complete installation can be achieved in hours without the need for specialist tools or skills.
PLEASE NOTE. This is intended as a guide only and is dependent on Ausgrid Energy prices. The above calculation is based @ 26¢/kwatt/hr. We have assumed that the heating is ‘ON’ for 6 hours a day (3 hours in the morning and 3 hours at night). Cost per month has been calculated @ 31 days per month. Every 1°C reduction in the temperature setting of your thermostat will result in a 5%-8% reduction in power usage and cost over 24 hours. The calculation of running costs can only be approximate. The actual cost will depend on a number of considerations – user preferences, temperature and switch-on time setpoints, cost of energy etc.
All of Warmtech’s undercarpet heaters are 100% water resistant.
The length of time it takes to warm the floor will depend upon the density of the carpet and the sub floor. As with undertile heating, an uninsulated concrete floor will take longer to heat up but will retain the heat for longer. Undercarpet heating will not provide you with an instant source of concentrated heat in the manner of a fireplace or bar heater. Rather the whole room is gradually warmed at the same time.
A typical installation will cost approximately 1.5** cents per hour per square meter of heated area when warming up. Once the floor has warmed up the thermostat switches the heater on and off automatically. In normal winter conditions if the heater is the only source of heat in a reasonably insulated room you can expect the heater to be on for between 30% and 50% of the time. This time will obviously vary depending upon the climatic conditions and the comfort levels required. Every 1ºC reduction in the temperature setting of your thermostat will result in a 6% reduction in power usage over 24 hours.
An average bathroom (500 watts) will cost approx $15 to $20 per month using an electronic floor thermostat at normal operating temperature.
** Please be aware that actual costs will vary between electricity supply companies.
Programming saves money because you do not unnecessarily heat your home when heating isn’t required, i.e. during the day while you’re at work. By lowering the heat during the day, you can realise significant savings: each 1ºC the temperature is lowered during an eight-hour period equals a savings of 2%.
If your room is well insulated and complies with modern insulation levels as set out in the current building regulations you should be able to use Warmtech Underfloor Heating as the sole heat source.
Warmtech has a range of specifically designed loose wire and matting heating systems for use under tile, natural stone and under carpet.
No specialist skills are not required. The Warmtech system is designed so that any contractor, or competent do-it-yourselfer, can install it. The kit comes with a comprehensive installation manual should you need any assistance during installation.
A qualified electrician should always undertake the connection of the heater to the thermostat.
Undertile Heating Systems: The heater should not be made fully operational until such time as the tile or concrete installer has confirmed that the cement materials (i.e. adhesive & grout) are fully cured. This may be anything from 1 – 3 weeks. Turning the system on too early could lead to the cement drying out too quickly, creating an unstable subfloor.
Underlaminate Heating Systems: Once wired and tested, the system may be switched on immediately
20 Sunny Bank Rd
Lisarow, NSW 2250
Phone: 1300 138 126
PO Box 262
Lilydale Vic 3140
Free Phone: 1300 138 126
Phone: +61 3 9735 3965
PO Box 39
Mitchell ACT 2911
Free Phone: 1300 138 126
Phone: +61 411 980944
69 Guthrie Street
Osborne Park WA 6017
Free Phone: 1300 138 126
Phone: +61 8 9244 5877